(Gelöst) Fernbedienung mit Atric-Ir per PCI to COM-Adapter (Fujitsu scaleo-e)

Archiv > General

(1/3) > >>

Andy:
Hallo
Ich wollte den Atric-Ir Einschalter auch per Lirc an einem MainBoard ohne "com" Anschluß betreiben.
Ich benutze für dieses vorhaben die 3.0.1.1.
Per FB kann ich den VDR starten und beenden...sollte also richtig angeschlossen sein.

Die richtige lircd.conf und eine remote.conf existieren auch, und sind an der richtigen Stelle.
Jetzt hab ich mir eine "2 Port Dual RS232 RS-232 DB9 Serial Port COM Device to PCI Adapter Converter Card"
geholt, und eingebaut.

Einen Stecker hab ich abgezogen und mit dem Atric-Ir verbunden.
Pin 1 ist auch an Pin1, das sollte also auch passen. Pin 5 Ground, passt auch.

Über's WebIf hab ich einmal lirc_serial Com1 und Com2 ausprobiert, aber ich habe leider kein Feedback der kleinen LED des Atric-Empfänger bekommen.
Hier noch zwei Bilder
https://www.wuala.com/Uhlstone/Public/Photos/Auswahl_013.png/?key=MKOLQyrwAZ7X
https://www.wuala.com/Uhlstone/Public/Photos/Auswahl_014.png/?key=MKOLQyrwAZ7X

Was mir komisch vorkommt...
...Setserial sagt...
setserial -g /dev/ttyS*
/dev/ttyS0, UART: undefined, Port: 0xef00, IRQ: 18
/dev/ttyS1, UART: unknown, Port: 0xee00, IRQ: 18
/dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4
/dev/ttyS3, UART: unknown, Port: 0x02e8, IRQ: 3

Komisch ist auch das bei einem mal "ttyS0" und beim nächsten hochfahren "ttyS1" "undefined" ist, so als wechselt es ständig.
Im VDR-Portal hatte ich mal gelesen das man bei so einer Karte noch die Option "share_irq=1" vergeben muß ?
Also z.B. "lirc_serial io=0xef00 irq=18 share_irq=1"

Link zum Thread http://www.vdr-portal.de/board60-linux/board14-betriebssystem/board68-debian-und-derivate/p790009-lirc-mit-ubuntu-und-pci-seriell-karte-hilfe/#post790009

Oder hab ich da etwas falsch gemacht ?

Hat noch einer ein heißen Tip für mich ? :o

EDIT: ein Log hab ich auch noch...

--- Quote ---Jan 13 18:40:09 (none) syslog.info syslogd started: BusyBox v1.21.1
Jan 13 18:40:09 (none) user.notice kernel: scsi 2:0:0:0: Direct-Access GENERIC USB Storage-SMC I19A PQ: 0 ANSI: 0 CCS
Jan 13 18:40:09 (none) user.notice kernel: sd 2:0:0:0: Attached scsi generic sg1 type 0
Jan 13 18:40:09 (none) user.notice kernel: sd 2:0:0:0: [sdb] Attached SCSI removable disk
Jan 13 18:40:09 (none) user.info kernel: usb 4-2: new full-speed USB device number 2 using uhci_hcd
Jan 13 18:40:09 (none) user.warn kernel: aufs test_add:264:mount[2595]: uid/gid/perm /var/spool/apm.mnt/locales 0/0/0777, 0/0/0775
Jan 13 18:40:09 (none) user.warn kernel: aufs test_add:264:mount[2628]: uid/gid/perm /var/spool/apm.mnt/install 0/0/0777, 0/0/0775
Jan 13 18:40:09 (none) user.info kernel: usb 5-2: new full-speed USB device number 2 using uhci_hcd
Jan 13 18:40:09 (none) user.warn kernel: aufs test_add:264:mount[2664]: uid/gid/perm /var/spool/apm.mnt/dvb 0/0/0777, 0/0/0775
Jan 13 18:40:09 (none) user.warn kernel: aufs test_add:264:mount[2677]: uid/gid/perm /var/spool/apm.mnt/dvb-usb 0/0/0777, 0/0/0775
Jan 13 18:40:09 (none) user.warn kernel: aufs test_add:264:mount[2690]: uid/gid/perm /var/spool/apm.mnt/network 0/0/0777, 0/0/0775
Jan 13 18:40:09 (none) user.info kernel: generic-usb 0003:1509:925D.0004: hiddev0: USB HID v1.10 Device [DM-140GINK Demo DM-140GINK Demo] on usb-0000:00:1d.3-2/input0
Jan 13 18:40:09 (none) user.info kernel: input: DM-140GINK Demo DM-140GINK Demo as /devices/pci0000:00/0000:00:1d.3/usb5/5-2/5-2:1.1/input/input3
Jan 13 18:40:09 (none) user.info kernel: generic-usb 0003:1509:925D.0005: input: USB HID v1.10 Device [DM-140GINK Demo DM-140GINK Demo] on usb-0000:00:1d.3-2/input1
Jan 13 18:40:09 (none) user.warn kernel: aufs test_add:264:mount[2731]: uid/gid/perm /var/spool/apm.mnt/webserver 0/0/0777, 0/0/0775
Jan 13 18:40:09 (none) user.info kernel: usb 1-4.2: new high-speed USB device number 8 using ehci_hcd
Jan 13 18:40:10 (none) user.info kernel: scsi3 : usb-storage 1-4.2:1.0
Jan 13 18:40:10 (none) user.warn kernel: aufs test_add:264:mount[2771]: uid/gid/perm /var/spool/apm.mnt/alsa 0/0/0777, 0/0/0775
Jan 13 18:40:10 (none) user.info kernel: usb 1-4.4: new low-speed USB device number 9 using ehci_hcd
Jan 13 18:40:10 (none) user.info kernel: input: 2.4G USB RF KeyBoard as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4.4/1-4.4:1.0/input/input4
Jan 13 18:40:10 (none) user.info kernel: generic-usb 0003:05AF:0319.0006: input: USB HID v1.10 Keyboard [2.4G USB RF KeyBoard] on usb-0000:00:1d.7-4.4/input0
Jan 13 18:40:10 (none) user.info kernel: input: 2.4G USB RF KeyBoard as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4.4/1-4.4:1.1/input/input5
Jan 13 18:40:10 (none) user.info kernel: generic-usb 0003:05AF:0319.0007: input: USB HID v1.10 Mouse [2.4G USB RF KeyBoard] on usb-0000:00:1d.7-4.4/input1
Jan 13 18:40:10 (none) user.warn kernel: aufs test_add:264:mount[2812]: uid/gid/perm /var/spool/apm.mnt/remote-autodetect 0/0/0777, 0/0/0775
Jan 13 18:40:10 (none) user.info kernel: input: 2.4G USB RF KeyBoard as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4.4/1-4.4:1.2/input/input6
Jan 13 18:40:10 (none) user.info kernel: generic-usb 0003:05AF:0319.0008: input,hiddev0: USB HID v1.10 Device [2.4G USB RF KeyBoard] on usb-0000:00:1d.7-4.4/input2
Jan 13 18:40:10 (none) user.warn kernel: aufs test_add:264:mount[2878]: uid/gid/perm /var/spool/apm.mnt/lib-x 0/0/0777, 0/0/0775
Jan 13 18:40:10 (none) user.warn kernel: aufs test_add:264:mount[2915]: uid/gid/perm /var/spool/apm.mnt/xorg 0/0/0777, 0/0/0775
Jan 13 18:40:10 (none) user.warn kernel: aufs test_add:264:mount[2957]: uid/gid/perm /var/spool/apm.mnt/xorg-autodetect 0/0/0777, 0/0/0775
Jan 13 18:40:10 (none) user.warn kernel: aufs test_add:264:mount[2976]: uid/gid/perm /var/spool/apm.mnt/vdr 0/0/0777, 0/0/0775
Jan 13 18:40:11 (none) user.warn kernel: aufs test_add:264:mount[2993]: uid/gid/perm /var/spool/apm.mnt/addons 0/0/0777, 0/0/0775
Jan 13 18:40:11 (none) user.notice kernel: scsi 3:0:0:0: Direct-Access JetFlash Transcend 8GB 8.07 PQ: 0 ANSI: 4
Jan 13 18:40:11 (none) user.notice kernel: sd 3:0:0:0: [sdc] 15687680 512-byte logical blocks: (8.03 GB/7.48 GiB)
Jan 13 18:40:11 (none) user.notice kernel: sd 3:0:0:0: [sdc] Write Protect is off
Jan 13 18:40:11 (none) user.debug kernel: sd 3:0:0:0: [sdc] Mode Sense: 23 00 00 00
Jan 13 18:40:11 (none) user.notice kernel: sd 3:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jan 13 18:40:11 (none) user.notice kernel: sd 3:0:0:0: Attached scsi generic sg2 type 0
Jan 13 18:40:11 (none) user.info kernel: sdc: sdc1
Jan 13 18:40:11 (none) user.notice kernel: sd 3:0:0:0: [sdc] Attached SCSI removable disk
Jan 13 18:40:11 (none) user.warn kernel: aufs test_add:264:mount[3032]: uid/gid/perm /var/spool/apm.mnt/setup 0/0/0777, 0/0/0775
Jan 13 18:40:11 (none) user.warn kernel: aufs test_add:264:mount[3049]: uid/gid/perm /var/spool/apm.mnt/lib-xine 0/0/0777, 0/0/0775
Jan 13 18:40:11 (none) user.warn kernel: aufs test_add:264:mount[3066]: uid/gid/perm /var/spool/apm.mnt/acpi 0/0/0777, 0/0/0775
Jan 13 18:40:11 (none) user.warn kernel: aufs test_add:264:mount[3083]: uid/gid/perm /var/spool/apm.mnt/mc 0/0/0777, 0/0/0775
Jan 13 18:40:11 (none) user.warn kernel: aufs test_add:264:mount[3100]: uid/gid/perm /var/spool/apm.mnt/ntfs 0/0/0777, 0/0/0775
Jan 13 18:40:11 (none) user.warn kernel: aufs test_add:264:mount[3117]: uid/gid/perm /var/spool/apm.mnt/ssh 0/0/0777, 0/0/0775
Jan 13 18:40:11 (none) user.warn kernel: aufs test_add:264:mount[3134]: uid/gid/perm /var/spool/apm.mnt/usb 0/0/0777, 0/0/0775
Jan 13 18:40:11 (none) user.warn kernel: aufs test_add:264:mount[3151]: uid/gid/perm /var/spool/apm.mnt/lib-pango 0/0/0777, 0/0/0775
Jan 13 18:40:12 (none) user.warn kernel: aufs test_add:264:mount[3168]: uid/gid/perm /var/spool/apm.mnt/xorg-nvidia 0/0/0777, 0/0/0775
Jan 13 18:40:12 (none) user.warn kernel: aufs test_add:264:mount[3185]: uid/gid/perm /var/spool/apm.mnt/lib-av 0/0/0777, 0/0/0775
Jan 13 18:40:12 (none) user.warn kernel: aufs test_add:264:mount[3202]: uid/gid/perm /var/spool/apm.mnt/dm140vfd 0/0/0777, 0/0/0775
Jan 13 18:40:12 (none) user.warn kernel: aufs test_add:264:mount[3219]: uid/gid/perm /var/spool/apm.mnt/devstatus 0/0/0777, 0/0/0775
Jan 13 18:40:12 (none) user.warn kernel: aufs test_add:264:mount[3236]: uid/gid/perm /var/spool/apm.mnt/extrecmenu 0/0/0777, 0/0/0775
Jan 13 18:40:12 (none) user.warn kernel: aufs test_add:264:mount[3253]: uid/gid/perm /var/spool/apm.mnt/femon 0/0/0777, 0/0/0775
Jan 13 18:40:12 (none) user.warn kernel: aufs test_add:264:mount[3270]: uid/gid/perm /var/spool/apm.mnt/perl 0/0/0777, 0/0/0775
Jan 13 18:40:12 (none) user.warn kernel: aufs test_add:264:mount[3287]: uid/gid/perm /var/spool/apm.mnt/epgsearch 0/0/0777, 0/0/0775
Jan 13 18:40:12 (none) user.warn kernel: aufs test_add:264:mount[3304]: uid/gid/perm /var/spool/apm.mnt/markad 0/0/0777, 0/0/0775
Jan 13 18:40:12 (none) user.warn kernel: aufs test_add:264:mount[3321]: uid/gid/perm /var/spool/apm.mnt/undelete 0/0/0777, 0/0/0775
Jan 13 18:40:13 (none) user.warn kernel: aufs test_add:264:mount[3338]: uid/gid/perm /var/spool/apm.mnt/backup 0/0/0777, 0/0/0775
Jan 13 18:40:13 (none) user.warn kernel: aufs test_add:264:mount[3355]: uid/gid/perm /var/spool/apm.mnt/python 0/0/0777, 0/0/0775
Jan 13 18:40:13 (none) user.warn kernel: aufs test_add:264:mount[3372]: uid/gid/perm /var/spool/apm.mnt/lib-curl 0/0/0777, 0/0/0775
Jan 13 18:40:13 (none) user.warn kernel: aufs test_add:264:mount[3389]: uid/gid/perm /var/spool/apm.mnt/xbmc 0/0/0777, 0/0/0775
Jan 13 18:40:13 (none) user.warn kernel: aufs test_add:264:mount[3406]: uid/gid/perm /var/spool/apm.mnt/osdteletext 0/0/0777, 0/0/0775
Jan 13 18:40:13 (none) user.warn kernel: aufs test_add:264:mount[3423]: uid/gid/perm /var/spool/apm.mnt/softhddevice 0/0/0777, 0/0/0775
Jan 13 18:40:13 (none) user.warn kernel: aufs test_add:264:mount[3441]: uid/gid/perm /var/spool/apm.mnt/tvguide 0/0/0777, 0/0/0775
Jan 13 18:40:13 (none) user.warn kernel: aufs test_add:264:mount[3458]: uid/gid/perm /var/spool/apm.mnt/trayopenng 0/0/0777, 0/0/0775
Jan 13 18:40:13 (none) user.warn kernel: aufs test_add:264:mount[3475]: uid/gid/perm /var/spool/apm.mnt/lib-imagemagick 0/0/0777, 0/0/0775
Jan 13 18:40:14 (none) user.warn kernel: aufs test_add:264:mount[3492]: uid/gid/perm /var/spool/apm.mnt/skinnopacity 0/0/0777, 0/0/0775
Jan 13 18:40:14 (none) user.warn kernel: aufs test_add:264:mount[3509]: uid/gid/perm /var/spool/apm.mnt/channellogos-nopacity 0/0/0777, 0/0/0775
Jan 13 18:40:14 (none) user.warn kernel: aufs test_add:264:mount[3526]: uid/gid/perm /var/spool/apm.mnt/lirc 0/0/0777, 0/0/0775
Jan 13 18:40:14 (none) user.warn kernel: aufs test_add:264:mount[3543]: uid/gid/perm /var/spool/apm.mnt/lib-xine-drivers 0/0/0777, 0/0/0775
Jan 13 18:40:17 (none) user.warn kernel: mount: sending ioctl 5310 to a partition!
Jan 13 18:40:17 (none) user.warn kernel: mount: sending ioctl 5310 to a partition!
Jan 13 18:40:17 (none) user.notice kernel: XFS (sda2): Mounting Filesystem
Jan 13 18:40:17 (none) user.info kernel: XFS (sda2): Ending clean mount
Jan 13 18:40:19 (none) user.info kernel: lirc_dev: IR Remote Control driver registered, major 253
Jan 13 18:40:19 (none) user.err kernel: lirc_serial: port existence test failed, cannot continue
Jan 13 18:40:20 (none) user.info kernel: 8139too: 8139too Fast Ethernet driver 0.9.28
Jan 13 18:40:20 (none) user.info kernel: 8139too 0000:01:06.0: eth0: RealTek RTL8139 at 0xf9104000, 00:40:ca:90:a9:5e, IRQ 18
Jan 13 18:40:22 (none) user.info kernel: 8139too 0000:01:06.0: eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
Jan 13 18:40:27 (none) user.info kernel: Linux agpgart interface v0.103
Jan 13 18:40:27 (none) user.info kernel: agpgart-intel 0000:00:00.0: Intel 915G Chipset
Jan 13 18:40:27 (none) user.info kernel: agpgart-intel 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable
Jan 13 18:40:27 (none) user.info kernel: agpgart-intel 0000:00:00.0: detected 8192K stolen memory
Jan 13 18:40:27 (none) user.info kernel: agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
Jan 13 18:40:31 (none) user.warn kernel: nvidia: module license 'NVIDIA' taints kernel.
Jan 13 18:40:31 (none) user.warn kernel: Disabling lock debugging due to kernel taint
Jan 13 18:40:31 (none) user.info kernel: vgaarb: device changed decodes: PCI:0000:02:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
Jan 13 18:40:31 (none) user.warn kernel: NVRM: loading NVIDIA UNIX x86 Kernel Module 319.32 Wed Jun 19 15:20:44 PDT 2013
Jan 13 18:40:33 (none) user.debug kernel: eth0: no IPv6 routers present
Jan 13 18:40:34 (none) user.warn kernel: NVRM: Your system is not currently configured to drive a VGA console
Jan 13 18:40:34 (none) user.warn kernel: NVRM: on the primary VGA device. The NVIDIA Linux graphics driver
Jan 13 18:40:34 (none) user.warn kernel: NVRM: requires the use of a text-mode VGA console. Use of other console
Jan 13 18:40:34 (none) user.warn kernel: NVRM: drivers including, but not limited to, vesafb, may result in
Jan 13 18:40:34 (none) user.warn kernel: NVRM: corruption and stability problems, and is not supported.
Jan 13 18:40:38 (none) user.err kernel: WARNING: You are using an experimental version of the media stack.
Jan 13 18:40:38 (none) user.err kernel:    As the driver is backported to an older kernel, it doesn't offer
Jan 13 18:40:38 (none) user.err kernel:    enough quality for its usage in production.
Jan 13 18:40:38 (none) user.err kernel:    Use it with care.
Jan 13 18:40:38 (none) user.err kernel: Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
Jan 13 18:40:38 (none) user.err kernel:    dfb9f94e8e5e7f73c8e2bcb7d4fb1de57e7c333d [media] stk1160: Build as a module if SND is m and audio support is selected
Jan 13 18:40:38 (none) user.err kernel:    9f1595245574a2dc1fb375df665e4d9fe336a9c4 [media] cx23885-video: fix two warnings
Jan 13 18:40:38 (none) user.err kernel:    5bc08e1921e46101457d3be09835697490177fdd [media] cx23885[v4]: Fix interrupt storm when enabling IR receiver
Jan 13 18:40:38 (none) user.err kernel:    experimental: 7631b6e10c42669d290362c13fee7da3be35a8da experimental: Basic support for parallel build ('make -jN')
Jan 13 18:40:38 (none) user.err kernel:    ngene-octopus-test: 406ffecccbec6e22da954a07b7398292330bc767 ddbridge: Add ID of Digital Devices Octopus V3.
Jan 13 18:40:38 (none) user.err kernel:    v4l-dvb-saa716x: 0dab24906ff057b72537b01605bdf06c4dbb1c62 saa716x: i2c_del_adapter() fix
Jan 13 18:40:38 (none) user.info kernel: saa7146: register extension 'budget dvb'
Jan 13 18:40:38 (none) user.info kernel: saa7146: found saa7146 @ mem f84ea000 (revision 1, irq 16) (0x13c2,0x1018)
Jan 13 18:40:38 (none) user.warn kernel: saa7146 (0): dma buffer size 192512
Jan 13 18:40:38 (none) user.info kernel: DVB: registering new adapter (TT-Budget-S-1401 PCI)
Jan 13 18:40:38 (none) user.warn kernel: adapter has MAC addr = 00:d0:5c:d3:09:65
Jan 13 18:40:38 (none) user.info kernel: LNBx2x attached on addr=8
Jan 13 18:40:38 (none) user.info kernel: budget dvb 0000:01:01.0: DVB: registering adapter 0 frontend 0 (Philips TDA10086 DVB-S)...
Jan 13 19:40:41 (none) user.err vdr: [5322] DM140VFD: Font 'Sans:Bold' not found, using default Sans:Bold
Jan 13 18:40:46 (none) user.info kernel: input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input7
Jan 13 18:40:46 (none) user.info kernel: ACPI: Power Button [PWRB]
Jan 13 18:40:46 (none) user.info kernel: input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input8
Jan 13 18:40:46 (none) user.info kernel: ACPI: Power Button [PWRF]
Jan 13 18:40:46 (none) user.info kernel: ACPI: Fan [FAN] (on)
Jan 13 18:40:46 (none) user.info kernel: thermal LNXTHERM:00: registered as thermal_zone0
Jan 13 18:40:46 (none) user.info kernel: ACPI: Thermal Zone [THRM] (26 C)
Jan 13 19:40:46 (none) daemon.info acpid: starting up with proc fs
Jan 13 19:40:46 (none) daemon.info acpid: 1 rule loaded
Jan 13 19:40:46 (none) daemon.info acpid: waiting for events: event logging is off
Jan 13 19:40:55 (none) user.err vdr: [6790] DM140VFD: close() done
Jan 13 19:40:55 (none) user.err vdr: [6795] DM140VFD: close() done
Jan 13 18:40:57 (none) user.info kernel: bootsplash: status on console 0 changed to on
Jan 13 19:40:57 (none) auth.info login[6950]: root login on 'tty1'
Jan 13 19:40:57 (none) auth.info login[6952]: root login on 'tty2'
Jan 13 19:40:57 (none) auth.info login[6956]: root login on 'tty3'
Jan 13 19:40:57 (none) auth.info login[6962]: root login on 'tty4'
Jan 13 18:43:36 (none) user.warn kernel: saa7146: saa7146 (0) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer
Jan 13 18:46:20 (none) user.warn kernel: saa7146: saa7146 (0) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer
Jan 13 18:47:21 (none) user.warn kernel: saa7146: saa7146 (0) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer
Jan 13 18:48:16 (none) user.warn kernel: saa7146: saa7146 (0) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer
Jan 13 18:50:50 (none) user.warn kernel: saa7146: saa7146 (0) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer
Jan 13 18:50:53 (none) user.warn kernel: saa7146: saa7146 (0) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer
Jan 13 19:53:10 (none) user.err vdr: [5399] ERROR: lircd connection broken, trying to reconnect every 3,0 seconds
Jan 13 18:53:11 (none) user.info kernel: lirc_dev: IR Remote Control driver registered, major 253
Jan 13 18:53:11 (none) user.err kernel: lirc_serial: port existence test failed, cannot continue
Jan 13 19:54:50 (none) user.err vdr: [5399] ERROR: lircd connection broken, trying to reconnect every 3,0 seconds
Jan 13 19:55:05 (none) user.err vdr: [5399] ERROR: lircd connection broken, trying to reconnect every 3,0 seconds
Jan 13 18:55:06 (none) user.info kernel: lirc_dev: IR Remote Control driver registered, major 253
Jan 13 18:55:06 (none) user.err kernel: lirc_serial: port 02f8 already in use
Jan 13 18:55:06 (none) user.warn kernel: lirc_serial: use 'setserial /dev/ttySX uart none'
Jan 13 18:55:06 (none) user.warn kernel: lirc_serial: or compile the serial port driver as module and
Jan 13 18:55:06 (none) user.warn kernel: lirc_serial: make sure this module is loaded first
Jan 13 18:59:15 (none) user.warn kernel: saa7146: saa7146 (0) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer
Jan 13 19:01:29 (none) user.warn kernel: saa7146: saa7146 (0) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer

--- End quote ---
LG
Andre

t-bird.de:
Hallo Andy,

was sagt denn das BIOS? Bei manchen Boards kann man trotz fehlender COM-Ports (oder wenn solch eine Erweiterungskarte verbaut wurde) Einstellungen zu diesen vornehmen.

Die COMs sind normalerweise auf einstelligen IRQs. Und bei dir liegen ttyS0 und S1 auf IRQ18. Hingegen die ttyS2 und S3 auf den "richtigen" IRQs. Gibt es Jumper auf der Karte?

LG

t-bird

Andy:
Hi t-bird
Im Bios gab es bevor ich die Karte eingestegt habe, keine Einstellmöglichkeiten...werde da aber morgen nochmal genauer nach schauen.
Auf der Karte gibt es keine Jumper.

LG
Andre

Delaney:
Moin,
ist ja ewig her das ich mal was mit setserial zu tun hatte, da hatte mein ISDN-Modem noch ne serielle Schnittstelle ...
Mal schauen ob meine Zellen das noch passend abrufen ;)

--- Quote from: Andy on January 13, 2014, 20:40:18 ---Was mir komisch vorkommt...
...Setserial sagt...
setserial -g /dev/ttyS*
/dev/ttyS0, UART: undefined, Port: 0xef00, IRQ: 18
/dev/ttyS1, UART: unknown, Port: 0xee00, IRQ: 18
/dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4
/dev/ttyS3, UART: unknown, Port: 0x02e8, IRQ: 3

--- End quote ---
0-3 ist der normale standard Bereich dieser alten Legacy-Schnittstelle, was nicht bedeutet das die alle vorhanden sind.
Einziges Indiz ist UART: undefined anstelle von UART: unknown
Bei ttyS0 würde ich daher mal testen ob nicht autoconfig was passendes findet, also z.B.

--- Code: ---setserial /dev/ttyS0 autoconfig
setserial /dev/ttyS0 -av
--- End code ---
Oder gängige UART Typen durchprobieren, z.B.

--- Code: ---setserial /dev/ttyS0 uart 16450
--- End code ---
alternative Uarts wären 16550, 16550A, 16650, 16650V2, 16654, 16750, 16850, 16950, 16954
(8250 hab ich mal weggelassen)
uart none wäre wenig sinnvoll, das schaltet den Port ab.
Welcher von den beiden Ports der Karte dann ttyS0 oder S1 ist mußt evtl auch ausprobieren.
Lag bei der Karte irgendeine Software dabei? Wenn dann wohl nur Dos/Windows

Was share_irq=1 angeht wäre 'cat /proc/interrupts' hilfreich

Andy:
Hallo Delaney

Bei...

--- Quote ---setserial /dev/ttyS0 autoconfig
--- End quote ---
...kommt nix, aber bei...

--- Quote ---setserial /dev/ttyS0 -av
--- End quote ---
...kommt...

--- Quote ---MLD> setserial /dev/ttyS0 -av
/dev/ttyS0, Line 0; UART: undefined, Port: 0xef00, IRQ: 18
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000
Flags: spd_normal skip_test
--- End quote ---

Bei cat /proc/interrupts kommt...

--- Quote --- CPU0
0: 127 IO-APIC-edge timer
1: 3 IO-APIC-edge i8042
6: 2 IO-APIC-edge floppy
8: 0 IO-APIC-edge rtc0
9: 0 IO-APIC-fasteoi acpi
14: 177 IO-APIC-edge ide0
15: 0 IO-APIC-edge ide1
16: 29953 IO-APIC-fasteoi uhci_hcd:usb5, nvidia, snd_hda_intel, saa7146 (0)
18: 725 IO-APIC-fasteoi uhci_hcd:usb4, eth0
19: 2174 IO-APIC-fasteoi ata_piix, uhci_hcd:usb3
23: 1771 IO-APIC-fasteoi ehci_hcd:usb1, uhci_hcd:usb2
NMI: 0 Non-maskable interrupts
LOC: 146767 Local timer interrupts
SPU: 0 Spurious interrupts
PMI: 0 Performance monitoring interrupts
IWI: 0 IRQ work interrupts
RTR: 0 APIC ICR read retries
RES: 0 Rescheduling interrupts
CAL: 0 Function call interrupts
TLB: 0 TLB shootdowns
ERR: 0
MIS: 0
--- End quote ---

Das heißt also ich muß das so abändern ?

--- Quote ---# Lirc Aufruf Argumente
Lirc_ARGS="/dev/ttyS0 uart 115200"
# Lirc Driver
LIRC_DRIVER="lirc_serial irq=18 io=0xef00
--- End quote ---

EDIT: Bios Einstellungen für Serial Port's gibt es definitiv nicht.
Aber es waren Linuxtreiber dabei, wo es heißt...

--- Quote ---This installation guide describes the procedures to install and uninstall CH352 PCI to two serial ports,one serial and one parport,one parport in Linux platform.
1-install and uninstall CH352 PCI to two serial ports

1-install and uninstall CH352 PCI to two serial ports
(1)-install
<1>-copy install_ss_80x86.o to /usr/sbin
<2>-Add /usr/sbin/install_ss_80x86 at the end of the /etc/rc.d/rc.local.
<3>-reboot
The ttyS2 and ttyS3 are ready for application.
(2)-uninstall
(1)-Remove /usr/sbin/install_ss_80x86 at the end of the /etc/rc.d/rc.local.
(2)-Remove /usr/sbin/install_ss_80x86.o

--- End quote ---

LG
Andre

Navigation

[0] Message Index

[#] Next page

Go to full version