Archiv > Raspberry PI
Test MLD-4 RPI tgz
gkd-berlin:
Hallo,
Neuinstallation der MLD-4.0.0-rpi_rpi_2014.04.22-56.tar vom 22.4. 1:27h
Kaltstart von SD-Karte:
Nach Hochfahren:
--- Code: ---/var/log/sysinit
Searching for boot device: /
Boot device is: /dev/mmcblk0p1
...
modprobe: can't open 'modules.dep': No such file or directory done
...
Collected errors:
* satisfy_dependencies_for: Cannot satisfy the following dependencies for suspend:
* libcec *
* opkg_install_cmd: Cannot install package suspend. failed
--- End code ---
Vom TV abgeschrieben:
--- Code: ---Copy initramfs to tmpfs:
/etc/init.d/rc.sysinit: /etc/profile: line 13: /opt/vc/lib: Permission denied
Import filesystems
--- End code ---
Die 2. Zeile fehlt in der Sysinit.
Keine Fehlermeldungen in der Messages:
--- Code: ---/var/log/messages
Jan 1 00:02:34 (none) user.info kernel: [ 154.963612] input: Sundtek Ltd. Remote Control as /devices/virtual/input/input2
Jan 1 00:02:34 (none) user.info kernel: [ 155.147221] input: lircd as /devices/virtual/input/input3
--- End code ---
Es reagieren 7 Tasten auf der zum DVB-Stick mitgelieferten FB, aber völlig falsch.
Installation auf Festplatte
Nach 1. reboot
Die Sysinit ist leer !
In der Messages jede Menge Fehlermeldungen:
--- Code: ---/var/log/messages
Jan 1 00:02:26 (none) syslog.info syslogd started: BusyBox v1.22.1
Jan 1 00:02:29 (none) user.info kernel: [ 150.285702] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
Jan 1 00:02:29 (none) user.info kernel: [ 150.333517] input: Sundtek Ltd. Remote Control as /devices/virtual/input/input2
Jan 1 00:02:30 (none) user.info kernel: [ 150.533530] input: lircd as /devices/virtual/input/input3
Jan 1 00:02:31 (none) user.info kernel: [ 151.992857] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Jan 1 00:03:25 (none) user.info kernel: [ 205.641479] btrfs: device fsid 597eaba3-43ef-424c-ab24-017901f58880 devid 1 transid 57 /dev/sda1
Jan 1 00:03:25 (none) user.info kernel: [ 205.660299] btrfs: disk space caching is enabled
Jan 1 00:03:28 (none) user.notice kernel: [ 209.291674] XFS (sda2): Mounting Filesystem
Jan 1 00:03:29 (none) user.info kernel: [ 209.585342] XFS (sda2): Ending clean mount
Jan 1 01:04:15 (none) auth.info login[6822]: root login on 'tty2'
Jan 1 01:04:15 (none) auth.info login[6829]: root login on 'tty4'
Jan 1 01:04:15 (none) auth.info login[6821]: root login on 'tty1'
Jan 1 01:04:15 (none) auth.info login[6825]: root login on 'tty3'
Jan 1 00:09:31 (none) user.info kernel: [ 572.263517] btrfs: device fsid 4dec4903-635a-498f-b38f-f309c439d413 devid 1 transid 4 /dev/sda1
Jan 1 00:09:31 (none) user.info kernel: [ 572.276798] btrfs: disk space caching is enabled
Jan 1 00:09:31 (none) user.info kernel: [ 572.398806] btrfs: creating UUID tree
Jan 1 00:09:32 (none) user.info kernel: [ 572.704108] btrfs: setting 2 feature flag
Jan 1 01:00:16 (none) syslog.info syslogd started: BusyBox v1.22.1
Jan 1 01:00:20 (none) user.info kernel: [ 21.830792] input: Sundtek Ltd. Remote Control as /devices/virtual/input/input2
Jan 1 01:00:21 (none) user.info kernel: [ 22.554038] input: lircd as /devices/virtual/input/input3
Jan 1 01:00:22 (none) user.info kernel: [ 23.633892] input: Sundtek Ltd. Remote Control (lircd bypass) as /devices/virtual/input/input4
Jan 1 01:00:23 (none) user.info kernel: [ 24.586671] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
Jan 1 01:00:25 (none) user.info kernel: [ 26.102226] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Apr 22 18:48:40 (none) user.err vdr: [1975] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 22 18:48:40 (none) user.err vdr: [1975] ERROR: remote control LIRC not ready!
Apr 22 18:48:40 (none) user.err vdr: [2004] ERROR: lircd connection broken, trying to reconnect every 3,0 seconds
Apr 22 18:48:43 (none) user.err vdr: [2004] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 22 18:48:46 (none) user.err vdr: [2004] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 22 18:48:49 (none) user.err vdr: [2004] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 22 18:48:52 (none) user.err vdr: [2004] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
und immer so weiter.
--- End code ---
Nach 2. reboot
--- Code: ---/var/log/sysinit
Import filesystems:
Turn on DMA:
Checking:
Btrfs Btrfs v0.19
done
Mounting:
done
Setting up logging: level 1
Setting up netware:
done
btrfs:
locales:
Setting timezone:
done
Load keymap: de-latin1
done
ntp-client:
rpi:
network:
eventlircd:
Starting eventlircd
done
Init networking
Starting DHCP-client
done
done
Starting ntp client:
22 Apr 19:12:00 ntpdate[1771]: step time server 5.9.80.114 offset 1398186679.299177 sec
done
vdr:
lirc:
Starting VDR
done
opkg:
alsa:
hdparm:
irxevent:
irexec:
ntfs-3g:
sensors:
ssh:
devmon:
vdr-plugin-opkg:
setup:
vdradmin-am:
webserver:
# Sensors
Starting devmon
done
Setting up storage devices
done
[2206] Apr 22 19:12:25 Running in background
Init sound card:
Restore sound settings:
done
Starting sshd:
Listen on IP: 192.168.2.101
done
Starting webserver:
done
[2616] Apr 22 19:12:57 Child connection from 192.168.2.102:1675
[2616] Apr 22 19:13:03 Password auth succeeded for 'root' from 192.168.2.102:1675
Starting vdradmin server:
done
--- End code ---
In der Messages wieder Fehlermeldungen:
--- Code: ---/var/log/messages
Jan 1 01:00:16 (none) syslog.info syslogd started: BusyBox v1.22.1
Jan 1 01:00:21 (none) user.info kernel: [ 21.823767] input: Sundtek Ltd. Remote Control as /devices/virtual/input/input2
Jan 1 01:00:21 (none) user.info kernel: [ 22.613852] input: lircd as /devices/virtual/input/input3
Jan 1 01:00:22 (none) user.info kernel: [ 23.695302] input: Sundtek Ltd. Remote Control (lircd bypass) as /devices/virtual/input/input4
Jan 1 01:00:23 (none) user.info kernel: [ 24.346211] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
Jan 1 01:00:25 (none) user.info kernel: [ 25.893125] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Apr 22 19:12:11 (none) user.err vdr: [1967] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 22 19:12:11 (none) user.err vdr: [1967] ERROR: remote control LIRC not ready!
Apr 22 19:12:11 (none) user.err vdr: [1996] ERROR: lircd connection broken, trying to reconnect every 3,0 seconds
Apr 22 19:12:14 (none) user.err vdr: [1996] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 22 19:12:17 (none) user.err vdr: [1996] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 22 19:12:20 (none) user.err vdr: [1996] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 22 19:12:23 (none) user.err vdr: [1996] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 22 19:12:26 (none) user.err vdr: [1996] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 22 19:12:29 (none) user.err vdr: [1996] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
usw.
--- End code ---
Die /var/log/vdr ist immer leer.
Ich glaube, beim Herunterfahren nach dem 1. reboot, erscheinen 3 Fehlermeldungen. Zeile 50 ... in rc.----- mehr konnte ich mir nicht merken. Vielleicht liegt es daran.
WIN-TV-Fernbedienung an GPIO:
Meine lircd.conf nach /etc kopiert
In der rc.config steht jetzt:
--- Code: ---# Lirc Aufruf Argumente
LIRC_ARGS=""
# Lirc modul to use
LIRC_MODUL="rpi on GPIO"
--- End code ---
--- Code: ---MLD> evtest
No device specified, trying to scan all of /dev/input/event*
Available devices:
/dev/input/event0: HID 04d9:1400
/dev/input/event1: HID 04d9:1400
/dev/input/event2: Sundtek Ltd. Remote Control
/dev/input/event3: lircd
/dev/input/event4: Sundtek Ltd. Remote Control (lircd bypass)
Select the device event number [0-4]: 3
--- End code ---
K e i n e Reaktion Ist aber egal, es funktioniert ja.
irw gestartet:
--- Code: ---MLD> irw
00000000000017e0 00 KEY_UP lircd.conf
00000000000017e1 00 KEY_DOWN lircd.conf
00000000000017e1 01 KEY_DOWN lircd.conf
00000000000017d0 00 KEY_RIGHT lircd.conf
--- End code ---
Hurra es läuft und läuft.
Nun muß ich nur noch ein wenig die Tastenbelegung nach meinen Wünschen abändern.
Wenn ich noch einmal eine lircd.conf anlegen will, klappt das nicht mehr.
Mit:
--- Code: ---MLD> irrecord -n lircd.conf -d /dev/lirc0
irrecord - application for recording IR-codes for usage with lirc
Copyright (C) 1998,1999 Christoph Bartelmus(lirc@bartelmus.de)
irrecord: could not open /dev/lirc0
irrecord: default_init(): Device or resource busy
irrecord: could not init hardware (lircd running ? --> close it, check permissions)
--- End code ---
Nach einem stop lirc fehlt lirc_rpi.
--- Code: ---MLD> lsmod
Module Size Used by Tainted: G
uinput 6548 1
i2c_bcm2708 4005 0
snd_bcm2835 18182 0
snd_pcm 82038 1 snd_bcm2835
snd_page_alloc 5164 1 snd_pcm
snd_timer 20413 1 snd_pcm
snd 59096 3 snd_bcm2835,snd_pcm,snd_timer
fuse 80405 0
MLD>
--- End code ---
Was muß ich eingeben, um eine lircd.conf zu erzeugen?
Ein besonderes Lob an Claus, Du hast es wieder einmal gepackt.
Und, epgsearch fehlt noch in der Pluginliste.
Gruß Gerhard
@Claus: Ih habe Deinen Beitrag eben erst gelesen. Kann ich für den Test das jetzt installierte System benutzen ?
clausmuus:
Hi,
die Fehler am Anfang Deines Reports sollten inzwischen behoben sein.
Für den Test musst Du ne ältere Version als Ausgangspunkt nehmen.
Um irrecord nutzen zu können, musst Du nach dem stoppen von lirc das Modul lirc_rpi laden: "modprobe lirc_rpi"
Claus
gkd-berlin:
Hallo Claus,
Upgrade-Test mit MLD-4.0.0-rpi_rpi_2014.04.14-56.tar vom 14.4. 23:48h
UPGRADES:
opkg, busybox, base, eventlircd, dvb-sundtek, rpihddevice, vc, sensors, lirc, vdr, suspend, ntfs-3g, network, udev, alsa, kernel, setup, dvb und mld-remote.
Installiert mit: All packages.
Statusmeldungen während der Installation (nur der letzte Block):
--- Code: ---setup:
Configuring opkg.
Configuring busybox.
Configuring base.
Configuring kernel.
Configuring eventlircd.
Configuring alsa.
Configuring dvb-sundtek.
Configuring vdr.
Configuring vc.
Configuring vdr-plugin-rpihddevice.
Configuring sensors.
Configuring liblockdev1.
Configuring lirc.
Configuring libcec2.
Configuring suspend.
Configuring ntfs-3g.
Configuring network.
Configuring udev.
Configuring vdr-plugin-setup.
Configuring dvb.
Configuring mld-remote.
Collected errors:
* resolve_conffiles: Existing conffile /etc/fstab is different from the conffile in the new package. The new conffile will be placed at /etc/fstab-opkg.
* resolve_conffiles: Existing conffile /etc/hosts is different from the conffile in the new package. The new conffile will be placed at /etc/hosts-opkg.
* resolve_conffiles: Existing conffile /etc/rc.config is different from the conffile in the new package. The new conffile will be placed at /etc/rc.config-opkg.
* resolve_conffiles: Existing conffile /etc/vdr/setup.conf is different from the conffile in the new package. The new conffile will be placed at /etc/vdr/setup.conf-opkg.
* resolve_conffiles: Existing conffile /etc/modprobe.d/custom.conf is different from the conffile in the new package. The new conffile will be placed at /etc/modprobe.d/custom.conf-opkg.
* file_md5sum_alloc: Failed to open file /etc/setup/modules: No such file or directory.
* resolve_conffiles: Existing conffile /etc/vdr/plugins/setup/setup.xml is different from the conffile in the new package. The new conffile will be placed at /etc/vdr/plugins/setup/setup.xml-opkg.
--- End code ---
REBOOT
--- Code: ---/var/log/sysinit
Import filesystems:
Turn on DMA:
Checking:
Btrfs Btrfs v0.19
done
Mounting:
done
Setting up logging: level 1
Setting up netware:
done
btrfs:
locales:
Setting timezone:
done
Load keymap: de-latin1
done
ntp-client:
rpi:
network:
eventlircd:
Starting eventlircd
done
Init networking
Starting DHCP-client
done
done
Starting ntp client:
23 Apr 01:49:35 ntpdate[1813]: step time server 176.9.253.76 offset 1398210532.691199 sec
done
vdr:
lirc:
Starting VDR
done
hdparm:
ssh:
devmon:
vdr-plugin-opkg:
vdradmin-am:
webserver:
opkg:
sensors:
irxevent:
irexec:
ntfs-3g:
alsa:
setup:
# Sensors
Starting devmon
done
[2291] Apr 23 01:50:00 Running in background
Setting up storage devices
done
Init sound card:
done
Starting sshd:
Listen on IP: 192.168.2.101
done
Starting webserver:
done
Starting vdradmin server:
done
[2589] Apr 23 01:50:42 Child connection from 192.168.2.102:1883
[2589] Apr 23 01:50:48 Password auth succeeded for 'root' from 192.168.2.102:1883
--- End code ---
--- Code: ---/var/log/messages
Jan 1 01:00:18 (none) syslog.info syslogd started: BusyBox v1.22.1
Jan 1 01:00:22 (none) user.info kernel: [ 22.614648] input: Sundtek Ltd. Remote Control as /devices/virtual/input/input2
Jan 1 01:00:22 (none) user.info kernel: [ 23.284284] input: lircd as /devices/virtual/input/input3
Jan 1 01:00:23 (none) user.info kernel: [ 24.352387] input: Sundtek Ltd. Remote Control (lircd bypass) as /devices/virtual/input/input4
Jan 1 01:00:25 (none) user.info kernel: [ 25.604393] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
Jan 1 01:00:26 (none) user.info kernel: [ 27.160151] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Apr 23 01:49:47 (none) user.err vdr: [2042] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:49:47 (none) user.err vdr: [2042] ERROR: remote control LIRC not ready!
Apr 23 01:49:47 (none) user.err vdr: [2081] ERROR: lircd connection broken, trying to reconnect every 3,0 seconds
Apr 23 01:49:50 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:49:53 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:49:56 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:49:59 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:02 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:05 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:08 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:11 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:14 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:17 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:20 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:23 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:26 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:29 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:31 (none) auth.info login[2565]: root login on 'tty3'
Apr 23 01:50:31 (none) auth.info login[2562]: root login on 'tty2'
Apr 23 01:50:31 (none) auth.info login[2561]: root login on 'tty1'
Apr 23 01:50:31 (none) auth.info login[2568]: root login on 'tty4'
Apr 23 01:50:32 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:35 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:38 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:41 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:44 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
Apr 23 01:50:47 (none) user.err vdr: [2081] ERROR (lirc.c,43): /var/run/lirc/lircd: No such file or directory
usw.
--- End code ---
Die Kiste läuft!
Ich hoffe, es hilft Dir weiter.
Gruß Gerhard
clausmuus:
Danke,
ja, nun weiß ich das die Änderung auch nen fehlerfreien Upgrade des Kernel ermöglicht.
Claus
gkd-berlin:
Hallo,
Test: MLD-4.0.0-rpi_rpi_2014.04.22-56.tar vom 22.4. 20:53h
Kaltstart von der SD-Karte. Hier taucht die Fehlermeldung
--- Code: ---Collected errors:
* satisfy_dependencies_for: Cannot satisfy the following dependencies for suspend:
* libcec *
* opkg_install_cmd: Cannot install package suspend. failed
--- End code ---
auf.
Nach Installation auf Festplatte ist suspend nicht aktiv. Es erscheint nicht in der System info.
F12 geht in Poweroff.
Wird suspend danach über Putty installiert, gibt es diese Fehlermeldung:
--- Code: ---MLD> opkg install suspend
Installing suspend (0-13) to root...
Downloading http://www.minidvblinux.de/download/4.0.0-rpi/files/base/suspend_0-13.opk.
Installing libcec2 (2.1.4-4) to root...
Downloading http://www.minidvblinux.de/download/4.0.0-rpi/files/libs/libcec2_2.1.4-4.opk.
Installing liblockdev1 (1.0.3-1) to root...
Downloading http://www.minidvblinux.de/download/4.0.0-rpi/files/libs/liblockdev1_1.0.3-1.opk.
Configuring liblockdev1.
Configuring libcec2.
Configuring suspend.
Collected errors:
* resolve_conffiles: Existing conffile /etc/rc.shutdown is different from the conffile in the new package. The new conffile will be placed at /etc/rc.shutdown-opkg.
MLD>
--- End code ---
Suspend ist in der System info zu sehen und wird korrekt ausgeführt.
epgsearch ist wieder da.
Putty ist auch ok.
Die Fernbedienung am GPIO funktioniert ebenfalls.
Einfach meine lircd.conf nach /etc kopiert und es klappt.
Gruß Gerhard
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version