MLD Forum
MLD-5.x => Systems => Raspberry PI => Topic started by: mafe68 on September 10, 2017, 14:32:19
-
Bei der Installation von vdr-plugin-skindesigner fehlen die Abhängigkeiten und die Installation schlägt fehl!
MLD> apt-get install vdr-plugin-skindesigner
Reading package lists... Done
Building dependency tree
Reading state information... Done
Some packages could not be installed. This may mean that you have
requested an impossible situation or if you are using the unstable
distribution that some required packages have not yet been created
or been moved out of Incoming.
The following information may help to resolve the situation:
The following packages have unmet dependencies:
vdr-plugin-skindesigner : Depends: sensors
E: Unable to correct problems, you have held broken packages.
-
Hi,
versuch jetzt bitte nochmal:
apt-get update
apt-get install vdr-plugin-skindesigner
Sollte nun wieder funktionieren.
-
Hi Andi!
Nein geht noch nicht, immer noch der Fehler das die Abhängigkeiten fehlen
-
Was sagt er denn wenn du nur sensors installieren willst?
-
Geht auch nicht mit folgenden Fehler!
MLD> apt-get install sensors
Reading package lists... Done
Building dependency tree
Reading state information... Done
Some packages could not be installed. This may mean that you have
requested an impossible situation or if you are using the unstable
distribution that some required packages have not yet been created
or been moved out of Incoming.
The following information may help to resolve the situation:
The following packages have unmet dependencies:
sensors:armhf-rpi2 : Depends: perl:armhf-rpi2 but it is not installable
E: Unable to correct problems, you have held broken packages.
-
Der sollte perl eigentlich aus dem armhf Repository nehmen, ich weiß nur nicht warum er das nicht macht.
Was steht denn bei dir im WebIF > System Informationen unter Systemarchitektur ?
-
Meinst du die System Information?
System
Name: MLD
Version: 5.4
Systemarchitektur: armhf armhf-rpi2
Paket Kategorie: unstable
Paket Version
alsa 1.1.3-42.4+4.4.50.198
appstarter 0-8.1
apt 1.4.7-70.4
at 3.1.20-9
backup 1-32.1
base 0-102.2
binutils 2.28-~1
btrfs 4.7.3-114.2+4.4.50.198
busybox 1:1.25.1-53
debug 0-2.6
dpkg 1.18.24-18
eventlircd 1:2016.03.15-37+4.4.50.198
font-config 0-5
hid 0-3+4.4.50.198
init 0-105.1
initramfs 2017.09.05-111.5
install 0-144.34
irkeytable 1.12.3-12.1
kernel 4.4.50.198-199.19
kodi 17.4-91.2
ldconfig 2.24-12
lirc 2:0.9.4-82.1
locales 0-25.4
locales-timezones 1-7
mergerfs 1:2.18.0-11.7
mld-remote 0-42
network 0-76.1+4.4.50.198
network-wireless 0-51.2
network-wireless-rpi3 0-1+4.4.50.198
openssl 1.1.0-2
pam 1.1.8-5
psplash 2009.05.28-22
python 2.7-12
python-kodi 2.7-7
python-talloc 2.1.8-~1
rc-core 2:0-15+4.4.50.198
rpi 0-42
rpi-firmware 2017.09.05-3
samba-libs 4.5.8-~89
ssh 7.4-15
tk8.6-blt2.5 2.5.3-~1
tools 0-20.2
udev 232-47.1
vdr 2.3.8.214.38-214.38
vdr-plugin-apt 0.1.0-12+2.3.8.214.38
vdr-plugin-dvbapi 1:2.2.4-10.4+2.3.8.214.38
vdr-plugin-rpihddevice 1:2017.04.24-40.2+2.3.8.214.38
vdr-plugin-satip 1:2.3.1-22.3+2.3.8.214.38
vdr-plugin-suspendoutput 2.1.0-9.1+2.3.8.214.38
vfat 0-1
webif 0-2.25
webserver 0-244.3
xfs 0-5
zlib1g 1.2.8-~1
-
Ich habe es jetzt gerade mal getestet mit einem RPI 2 und da gibts keine Probleme.
Mit nem RPI 3 müsste Claus mal testen, denn ich habe keinen.
-
RPi 2 und RPi 3 sind ja die selben Images? Nur beim RPi 2 sind die Wlan und Bluetooth Module nicht dabei. Da könnte ich ja das RPi 2 Images testen am RPi 3? Mal warten was Claus dazu sagt
-
Ja, ob RPI 2 oder 3 macht keinen Unterschied. Beim 3'er Image ist lediglich das WLAN Paket mehr mit dabei. Es funktionieren also beide Images für beide Systeme.
Mein RPI3 ist derzeit nicht frei, damit kann ich also nicht testen.
Claus
-
Ok dann werde ich morgen mal das Rpi 2 Images testen. Da Andi geschrieben hat das es bei ihm geht.
-
So habe jetzt das RPi 2 Images installiert am RPi 3 um zu testen ob man das vdr-plugin-skindesigner installieren kann. Da Andi geschrieben hat das es am RPi 2 funktioniert.
Nur geht es da auch nicht. Das Netinstall Image ist von heute mit dem ich die MLD 5.4 RPi 2 unstable installiert habe.
Hier die selbe Fehlermeldung wie beim RPi 3. Fehlende Abhängigkeiten.
MLD> apt-get install vdr-plugin-skindesigner
Reading package lists... Done
Building dependency tree
Reading state information... Done
Some packages could not be installed. This may mean that you have
requested an impossible situation or if you are using the unstable
distribution that some required packages have not yet been created
or been moved out of Incoming.
The following information may help to resolve the situation:
The following packages have unmet dependencies:
vdr-plugin-skindesigner : Depends: sensors
E: Unable to correct problems, you have held broken packages.
-
seltsam sensors gibt es nämlich:
3.4.0-9+4.4.50.198
was macht apt-get install sensors?
gruß
MarMic
-
Teste ich gleich nur beim letzten Test war es das selbe fehlende Abhängigkeiten. Stell gerade um auf testing um zu schauen ob es dort geht. nach stelle ich wieder auf unstable und versuche sensors zu installieren.
-
So hier die Ausgabe wenn ich das Paket "sensors" installieren will
MLD> apt-get install sensors
Reading package lists... Done
Building dependency tree
Reading state information... Done
Some packages could not be installed. This may mean that you have
requested an impossible situation or if you are using the unstable
distribution that some required packages have not yet been created
or been moved out of Incoming.
The following information may help to resolve the situation:
The following packages have unmet dependencies:
sensors:armhf-rpi2 : Depends: kernel:armhf-rpi2 (< 4.4.50.198-.) but 4.4.50.199.19-199.19 is to be installed
Depends: i2c:armhf-rpi2 but it is not going to be installed
Depends: perl:armhf-rpi2 but it is not installable
E: Unable to correct problems, you have held broken packages.
MLD>
-
Wo hast Du denn den Kernel her? Der unstable Kernel ist das jedenfalls nicht.
Claus
-
Das ist das Images von gestern und so habe ich nicht daran geändert. MLD-5.4_netinstall_2017.09.07-178.14+1636_armhf-rpi3.img
Das einzige was ich mal gemacht habe ist von unstable auf testing zu gehen und dann wieder zurück
Habe heute nochmal ein Image heruntergeladen und installiert und da ist auch das selbe.
Hier der Kernel von heute
MLD> uname -a
Linux MLD 4.4.50.198 #2 SMP Thu Sep 7 22:35:53 CEST 2017 armv7l GNU/Linux
Hier die Fehlermeldung von der Installation von skindesigner
MLD> apt-get install vdr-plugin-skindesigner
Reading package lists... Done
Building dependency tree
Reading state information... Done
Some packages could not be installed. This may mean that you have
requested an impossible situation or if you are using the unstable
distribution that some required packages have not yet been created
or been moved out of Incoming.
The following information may help to resolve the situation:
The following packages have unmet dependencies:
vdr-plugin-skindesigner : Depends: sensors
E: Unable to correct problems, you have held broken packages.
Hier von der Installation von sensors
MLD> apt-get install sensors
Reading package lists... Done
Building dependency tree
Reading state information... Done
Some packages could not be installed. This may mean that you have
requested an impossible situation or if you are using the unstable
distribution that some required packages have not yet been created
or been moved out of Incoming.
The following information may help to resolve the situation:
The following packages have unmet dependencies:
sensors:armhf-rpi2 : Depends: perl:armhf-rpi2 but it is not installable
E: Unable to correct problems, you have held broken packages.
Hier der Debug Code: He3OwB
-
OK, hab's überprüft. Das perl Paket fehlte bisher noch. Das wird jetzt gebaut und ist ne 15 Minuten verfügbar.
Claus
-
OK! Dann werde ich noch testen wenn das Paket gebaut ist
-
So jetzt konnte ich den skindesigner installieren nur jetzt ist das nächste Problem das weder ein OSD hat noch ein Bild. Es wird nur das MLD Logo angezeigt.
Im Log gibt er ständig die Fehlermeldung aus!
Sep 13 10:00:50 (none) user.err vdr: [6140] ERROR: invalid primary device number: 1
Sep 13 10:00:50 (none) user.err vdr: [6140] ERROR (ci.c,2990): (null): Bad address
Sep 13 10:01:01 (none) user.err vdr: [6215] ERROR: invalid primary device number: 1
Sep 13 10:01:01 (none) user.err vdr: [6215] ERROR: no primary device found - using first device!
Sep 13 10:01:01 (none) user.err vdr: [6215] ERROR: invalid primary device number: 1
Sep 13 10:01:01 (none) user.err vdr: [6215] ERROR (ci.c,2990): (null): Bad address
Hier noch der Debug Code: rH4Laj
-
So wie es aussieht sind durch die Installation von Skindesigner alle anderen Pakete deinstalliert worden. das sind die Pakete die nach Skindesiger noch installiert sind. Vorher war es einen RPi SATip Installation.
Paket Version
alsa 1.1.3-42.4+4.4.50.198
apt 1.4.7-70.4
at 3.1.20-9
backup 1-32.1
base 0-102.2
binutils 2.28-~1
btrfs 4.7.3-114.2+4.4.50.198
busybox 1:1.25.1-53
dbus 1.10.18-17
debug 0-2.6
dpkg 1.18.24-18
eventlircd 1:2016.03.15-37+4.4.50.198
font-config 0-5
font-dejavu 0-6
git 2.11.0-4
hid 0-3+4.4.50.198
i2c 3.1.2-13+4.4.50.198
icewm-lite 1.3.8-2
init 0-105.1
initramfs 2017.09.05-111.5
install 0-144.34
irkeytable 1.12.3-12.1
kernel 4.4.50.198-199.19
ldconfig 2.24-12
lirc 2:0.9.4-82.1
locales 0-25.4
mergerfs 1:2.18.0-11.7
mld-remote 0-42
mpg123 1.23.8-2
network 0-76.1+4.4.50.198
network-wireless 0-51.2
network-wireless-rpi3 0-1+4.4.50.198
openssl 1.1.0-2
pam 1.1.8-5
perl 5.24.1-14
psplash 2009.05.28-22
rc-core 2:0-15+4.4.50.198
rpi 0-42
rpi-firmware 2017.09.05-3
sensors 3.4.0-9+4.4.50.198
ssh 7.4-15
surf 0.7-10
udev 232-47.1
unzip 6.00-0
vdr 2.3.8.214.38-214.38
vdr-plugin-skindesigner 1.2.3-28.1+2.3.8.214.38
vfat 0-1
webif 0-2.25
webserver 0-244.3
xfs 0-5
xorg 1.19.2-90.4+4.4.50.198
zlib1g 1.2.8-~1
-
So jetzt habe ich wieder die Pakete installiert
vdr-plugin-apt
vdr-plugin-rpihddevice
und habe wieder ein OSD
Nur das SATIP mit vtuner Paket kann ich nicht mehr installieren mit folgender Fehlermeldung
MLD> apt-get install satip
Reading package lists... Done
Building dependency tree
Reading state information... Done
Some packages could not be installed. This may mean that you have
requested an impossible situation or if you are using the unstable
distribution that some required packages have not yet been created
or been moved out of Incoming.
The following information may help to resolve the situation:
The following packages have unmet dependencies:
satip : Depends: dvb-vtuner but it is not installable
E: Unable to correct problems, you have held broken packages.
-
So habe jetzt mal eine Neuinstallation gemacht und dabei Rpi-Satip ausgewählt nur nach der Installation ist nur MLD Base installiert.
Hier der Debug Code noch dazu: 0EXFGE
Der Log ist direkt nach der Neuinstallation und einem reboot des System.
Mach dazu einen neuen Beitrag auf sonst wird es hier zu unübersichtlich.
-
Skindesigner und auch Channellogos kann man jetzt installieren und funktioniert auch