[1] MLD-5.x / General / Atric Seriell IR Empfänger und IRW
 

Offline Matthias

  • Expert Member
  • *****
  • Posts: 1797
    • View Profile
    • http://www.mbudde.de
Atric Seriell IR Empfänger und IRW
« on: February 14, 2018, 10:38:15 »
Hallo Zusammen,

ich versuche mich momentan an der 5.4 testing 64 Bit.
Ich verwende den seriellen Atric IR Empfänger.
Bislang habe ich immer im Webif den Empfänger auswählen können - ich glaube es war Homebrew.
in der 5.4 finde ich aber weder was mit seriell oder Homebrew.
Was muss ich denn auswählen?

Und noch eine Frage.
Ich muss meine Lircd.conf/remote.conf nochmal anpassen.
Dazu wollte ich irw starten um die Tastenbelegung meiner Fernbedienung zu prüfen.
Irw kann ich in der Konsole starten, liefert aber keine Ausgabe.
Was mache ich falsch?

Grüße
Produktiv System:
SAT over IP - OctopusNet :
MLD 5.1 testing/64Bit , ASRock Q1900M J1900, Intel VA-API, 1 x 128 GB SSD + 1 x 3 TB HD, Atric LIRC/Com, ACPI Wakeup

Offline iNOB

  • Profi Member
  • ****
  • Posts: 282
    • View Profile
Atric Seriell IR Empfänger und IRW
« Reply #1 on: February 14, 2018, 14:22:38 »
Bei der 5.4 testing (x64) musste ich lediglich das Systempaket lirc und die lircd.conf auswählen. Zusätzlich noch den Haken bei "Ruckeln und prellen unterbinden" machen, das wars. Zumindst soweit ich mich entsinnen kann....  ???

Online clausmuus

  • Administrator
  • Expert Member
  • ********
  • Posts: 16293
    • View Profile
    • ClausMuus.de
Atric Seriell IR Empfänger und IRW
« Reply #2 on: February 14, 2018, 14:26:39 »
Im Fernbedienungs Setup muss COM1 ausgewählt werden.
MLD 5.1 - Raspberry PI - 7" Touch TFT - Squeeze Play
MLD 5.1 - lirc yaUsbIR - OctopusNet - XFX GeForce 9300 mit Intel E3200 - 2GB RAM - 6TB HDD - Lian Li PC-C37B - Samsung LE40A559
MLD 5.4 - OctopusNet - ASRock Q1900M - 2GB RAM 250GB HDD

Offline Matthias

  • Expert Member
  • *****
  • Posts: 1797
    • View Profile
    • http://www.mbudde.de
Atric Seriell IR Empfänger und IRW
« Reply #3 on: February 15, 2018, 13:58:26 »
Ok, mein Fehler.
Man sollte nicht 2 MLDs im Netz laufen lassen....

Also hangel ich mich mal weiter durch.
Auf COM1 gesetzt und meine lircd.conf hochgeladen.

Leider ohne Erfolg, keine Taste funktioniert.

Laut dmesg sollte die Hardware OK sein:
Code: [Select]
[   23.410041] serial_ir serial_ir.0: auto-detected active low receiver
[   23.459993] lirc_dev: IR Remote Control driver registered, major 249
[   23.462265] IR LIRC bridge handler initialized
[   23.579053] Registered IR keymap rc-rc6-mce
[   23.643634] IR RC6 protocol handler initialized
[   23.665091] rc rc0: Serial IR type home-brew as /devices/platform/serial_ir.0/rc/rc0
[   23.665170] input: Serial IR type home-brew as /devices/platform/serial_ir.0/rc/rc0/input11
[   23.665376] rc rc0: lirc_dev: driver ir-lirc-codec (serial_ir) registered at minor = 0
[   26.267133] input: lircd as /devices/virtual/input/input13
[ 9157.584398] serial_ir serial_ir.0: auto-detected active low receiver
[ 9157.584408] Registered IR keymap rc-rc6-mce
[ 9157.584471] rc rc0: Serial IR type home-brew as /devices/platform/serial_ir.0/rc/rc0
[ 9157.584548] input: Serial IR type home-brew as /devices/platform/serial_ir.0/rc/rc0/input15
[ 9157.584704] rc rc0: lirc_dev: driver ir-lirc-codec (serial_ir) registered at minor = 0

Code: [Select]
ir-keytable
Found /sys/class/rc/rc0/ (/dev/input/event11) with:
        Driver serial_ir, table rc-rc6-mce
        Supported protocols: lirc rc-5 rc-5-sz jvc sony nec sanyo mce_kbd rc-6 sharp xmp
        Enabled protocols: lirc rc-6
        Name: Serial IR type home-brew
        bus: 25, vendor/product: 0001:0001, version: 0x0100
        Repeat delay = 500 ms, repeat period = 125 ms

Code: [Select]
rc.config:
# Lirc Aufruf Argumente
LIRC_ARGS=""
LIRC_INSTALL_L2U="1"
LIRC_KEYMAP=""
# Lirc modul to use
LIRC_MODUL="serial on COM1"

Code: [Select]
lircd.conf:
#
# this config file was automatically generated
# using lirc-0.5.5pre8 on Sun Apr 18 11:43:45 1999
#
# contributed by Jens Leuschner <leuschner@gmx.net>
#
# brand:             Hauppauge
# model:
# supported devices: WinTV primo; WinTV pci; WinTV radio
#
# This config file will work with both homebrew receivers and
# original Hauppauge TV cards !!!
#



#
# this config file was automatically generated
# using lirc-0.6.6(animax) on Tue Apr 15 19:50:27 2003
#
# contributed by
#
# brand: Hauppauge
# model no. of remote control:
# devices being controlled by this remote: PVR 2/350
#


begin remote

name  Hauppauge_350
bits           13
flags RC5|CONST_LENGTH
eps            30
aeps          100

one           969   811
zero          969   811
plead        1097
gap          114605
toggle_bit      2
repeat_bit      2


begin codes
  KEY_PVR                  0x00000000000017BB
  KEY_POWER2               0x00000000000017BD        #  Was: Power
  KEY_TV                   0x000000000000179C        #  Was: TV
  KEY_VIDEO                0x0000000000001798        #  Was: Videos
  KEY_AUDIO                0x0000000000001799        #  Was: Music
  KEY_IMAGES               0x000000000000179A        #  Was: Pictures
  KEY_INFO                 0x000000000000178D        #  Was: Guide
  KEY_RADIO                0x000000000000178C        #  Was: Radio
  KEY_UP                   0x0000000000001794        #  Was: Up
  KEY_LEFT                 0x0000000000001796        #  Was: Left
  KEY_RIGHT                0x0000000000001797        #  Was: Right
  KEY_DOWN                 0x0000000000001795        #  Was: Down
  KEY_OK                   0x00000000000017A5        #  Was: OK
  KEY_ESC                  0x000000000000179F        #  Was: Back/Exit
  KEY_MENU                 0x000000000000179B
  KEY_VOLUMEUP             0x0000000000001790        #  Was: Vol+
  KEY_VOLUMEDOWN           0x0000000000001791        #  Was: Vol-
  KEY_MUTE                 0x000000000000178F        #  Was: Mute
  KEY_CHANNELUP            0x00000000000017A0        #  Was: Ch+
  KEY_CHANNELDOWN          0x00000000000017A1        #  Was: Ch-
  KEY_RECORD               0x00000000000017B7        #  Was: Record
  KEY_STOP                 0x00000000000017B6        #  Was: Stop
  KEY_PLAY                 0x00000000000017B5        #  Was: Play
  KEY_FORWARD              0x00000000000017B4        #  Was: Forward
  KEY_REWIND          0x00000000000017A4
  KEY_PAUSE                0x00000000000017B0        #  Was: Pause
  KEY_NEXT                0x000000000000179E
  KEY_1                    0x0000000000001781        #  Was: 1
  KEY_2                    0x0000000000001782        #  Was: 2
  KEY_3                    0x0000000000001783        #  Was: 3
  KEY_4                    0x0000000000001784        #  Was: 4
  KEY_5                    0x0000000000001785        #  Was: 5
  KEY_6                    0x0000000000001786        #  Was: 6
  KEY_7                    0x0000000000001787        #  Was: 7
  KEY_8                    0x0000000000001788        #  Was: 8
  KEY_9                    0x0000000000001789        #  Was: 9
  Asterix                  0x000000000000178A
  KEY_0                    0x0000000000001780        #  Was: 0
  KEY_NUMERIC_POUND        0x000000000000178E        #  Was: #
  KEY_RED                  0x000000000000178B        #  Was: Red
  KEY_GREEN                0x00000000000017AE        #  Was: Green
  KEY_YELLOW               0x00000000000017B8        #  Was: Yellow
  KEY_BLUE                 0x00000000000017A9        #  Was: Blue

end codes

end remote

Wie Marmic hier beschrieben: https://www.minidvblinux.de/forum/index.php/topic,8777.msg67583.html#msg67583 eventlircd Paket deinstalliert.
Immer noch keine Tasten :-(
Ich bin mit meinem Latein am Ende....
Produktiv System:
SAT over IP - OctopusNet :
MLD 5.1 testing/64Bit , ASRock Q1900M J1900, Intel VA-API, 1 x 128 GB SSD + 1 x 3 TB HD, Atric LIRC/Com, ACPI Wakeup

Offline Matthias

  • Expert Member
  • *****
  • Posts: 1797
    • View Profile
    • http://www.mbudde.de
Atric Seriell IR Empfänger und IRW
« Reply #4 on: February 15, 2018, 19:52:23 »
Könnte es sein das sich mein Problem dadurch verkompliziert weil ich keine DVB Karte habe (wegen SAT over IP)?

Produktiv System:
SAT over IP - OctopusNet :
MLD 5.1 testing/64Bit , ASRock Q1900M J1900, Intel VA-API, 1 x 128 GB SSD + 1 x 3 TB HD, Atric LIRC/Com, ACPI Wakeup

Online MarMic

  • Administrator
  • Expert Member
  • ********
  • Posts: 4675
    • View Profile
Atric Seriell IR Empfänger und IRW
« Reply #5 on: February 15, 2018, 19:54:14 »
glaube ich nicht! hat nichts miteinander zu tun!
SZVDR HD: Intel e5300@1,2ghz - Gigabyte GA-EP41-UD3L - 2GB ddr2 800 - Gainward G210 512mb - Silverstone LC16MR - DVBSky S952 - Astra 19,2 - MLD 5.4

WZVDR HD: Intel g1610@1,6ghz - Intel DH61BE - Scythe Big Shuriken 2 - 4GB ddr3 1333 - Asus GT610 1024mb - Chieftec Hi-Fi HM-02 - Tevii s480 - Astra 19,2 - MLD 5.4


Offline Matthias

  • Expert Member
  • *****
  • Posts: 1797
    • View Profile
    • http://www.mbudde.de
Atric Seriell IR Empfänger und IRW
« Reply #6 on: February 16, 2018, 08:54:02 »
Ich weiß ja nicht was ihr gemacht habt, aber mit dem Update von heute Morgen geht meine FB am Atric IR Empfänger.
Folgende Paket wurden neu installiert:

Code: [Select]
debug

0-2.8 => 0-2.8
init

0-105.2 => 0-105.3
initramfs

2018.02.13-111.8 => 2018.02.15-111.8
ssh

0-15 => 0-15.1
vdr-plugin-softhddevice

2018.02.10-74.20+2.3.8.214.51 => 2018.02.15-74.21+2.3.8.214.51
webif

0-2.33 => 0-2.34

Danke!!!
Produktiv System:
SAT over IP - OctopusNet :
MLD 5.1 testing/64Bit , ASRock Q1900M J1900, Intel VA-API, 1 x 128 GB SSD + 1 x 3 TB HD, Atric LIRC/Com, ACPI Wakeup

Online clausmuus

  • Administrator
  • Expert Member
  • ********
  • Posts: 16293
    • View Profile
    • ClausMuus.de
Atric Seriell IR Empfänger und IRW
« Reply #7 on: February 16, 2018, 11:36:08 »
Das dürfte nichts mit dem Update zu tun haben, denn da wurden in allen Paketen lediglich die localesierungs Dateien aktualisiert.
MLD 5.1 - Raspberry PI - 7" Touch TFT - Squeeze Play
MLD 5.1 - lirc yaUsbIR - OctopusNet - XFX GeForce 9300 mit Intel E3200 - 2GB RAM - 6TB HDD - Lian Li PC-C37B - Samsung LE40A559
MLD 5.4 - OctopusNet - ASRock Q1900M - 2GB RAM 250GB HDD

Offline Matthias

  • Expert Member
  • *****
  • Posts: 1797
    • View Profile
    • http://www.mbudde.de
Atric Seriell IR Empfänger und IRW
« Reply #8 on: February 16, 2018, 12:04:37 »
Hallo Claus,

merkwürdig ist es schon.
Ich habe meinen Test VDR gestartet = keine Remote
Update + VDRRestart = Remote funktioniert
Produktiv System:
SAT over IP - OctopusNet :
MLD 5.1 testing/64Bit , ASRock Q1900M J1900, Intel VA-API, 1 x 128 GB SSD + 1 x 3 TB HD, Atric LIRC/Com, ACPI Wakeup

[1] MLD-5.x / General / Atric Seriell IR Empfänger und IRW
 



Users Online Users Online

0 Members and 2 Guests are viewing this topic.